INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION

INTERSTATE COUNCIL FOR STANDARDIZATION. METROLOGY AND CERTIFICATION

INTERSTATE

STANDARD

COTTON AND FABRIC FABRICS FOR DOMESTIC

General specifications

Official edition

Foreword 1

The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic provisions "and GOST 1.2-97" Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. The procedure for development, acceptance, application, updating and cancellation "

Information about the standard

1 DEVELOPED by the Federal State Unitary Enterprise "Central Research Institute of the Cotton Industry" (FSUE TsNIKHBI)

2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology

3 ACCEPTED by the Interstate Council for Standardization, Metropology and Certification (Minutes No. 28 dated December 9, 2005)

Short name of the country according to MK<ИСО 3166) 004-97	Country code according to MK (ISO 31vv) 004-97	Abbreviated name of the national standardization body
		Armgosstandart
Kazakhstan		Gosstandart of the Republic of Kazakhstan
Kyrgyzstan		Kyrgyzstandard
		Moldova-Standard
the Russian Federation		Federal Agency for Technical Regulation
		nyu and metrology
Tajikistan		Tajikstandart
Turkmenistan		Glavgossluzkba "Turkmenstandartlary"
		State Standard of Ukraine

4 By order of the Federal Agency for Technical Regulation and Metrology dated May 10, 2006 No. 90-st, the interstate standard GOST 29298-2005 was put into effect as a national standard of the Russian Federation from January 1, 2007.

5 REPLACE GOST29298-92

Information on the entry into force (termination) of this standard is published in the index "National standards".

Information about changes to this standard is published in the index (catalog) "National standards". and the text of the changes is in the information signs "National Standards". In case of revision or cancellation of this standard, the corresponding information will be published in the information index "National standards"

In the Russian Federation, this standard cannot be fully or partially reproduced, replicated and distributed as an official publication without the permission of the Federal Agency for Technical Regulation and Metrology.

See the note of the Federal State Unitary Enterprise "STANDARTINFORM" (p. 9).

© STANDARTINFORM, 2006 © STANDARTINFORM. 2008 Reprinted (as of May 2008)

INTERSTATE STANDARD

COTTON AND MIXED FABRICS FOR HOUSEHOLD General specifications

Cotton and mixed domestic fabrics. General specifications

Date of introduction - 2007-01-01

1 area of ​​use

This standard applies to ready-made and gray cotton and blended fabrics used for the manufacture of products for dress, shirt and linen purposes, as well as items of clothing.

4.2.4 Fabrics are produced mercerized and not mercerized.

4.2.5 Fabrics, depending on the purpose, are produced with one of the types of finishing finishes. At the request of the consumer, the fabric is produced without finishing.

4.2.6 The fabrics used for the products of the children's assortment in terms of raw material composition must meet the requirements of the regulatory document. Fabrics for underwear assortment used for newborns and children of early, toddler and preschool ages must be produced without finishing.

4.2.7 Resizing after wet processing of finished fabrics must comply with the requirements. specified in table 2.

Table 2 - Change in dimensions after wet processing

Name of fabric Resizing after wet processing. %. less on the basis Dress (for dresses, blouses, dress suits, dressing gowns, shirts): Wrinkle-free finish, easy-ironing finish With an anti-shrink chemical finish, with a squeeze-out sizing agent based on thermosetting resins Shirts: Wrinkle-free finish, easy-ironing finish With an anti-shrink chemical finish, with a washable, thermosetting resin based finishing agent With a washable thermoplastic resin finish Lingerie: for underwear: Easy-iron finish, with a washable thermosetting resin finish With a washable thermoplastic resin finish for bed linen (including children without finishing) Notes (edit) 1 Fabrics with split pile are subjected to: corduroy cord and corduroy scar - dry cleaning or wet processing, velvet - dry cleaning. 2 For fabrics containing elastomeric threads, the change in linear dimensions after wet processing is not define.

4.2.8 Nominal widths for finished hemmed fabrics represent an integer of 70 cm or more ending in zero or five.

Tolerances for the width of fabrics in accordance with table 3.

4.2.9 The width of the two edges of the fabric should be no more than, cm:

3.0 - for fabric with split pile;

3.5 - for fabrics produced on a shuttleless loom;

1.5 - for other fabrics.

4.2.10 Grade of finished fabrics - according to GOST 161; harsh fabrics - according to the normative document.

4.2.11 * Breaking load and abrasion resistance of finished fabrics must meet the requirements of Table 4.

"See the note of the Federal State Unitary Enterprise" STANDARTINFORM "(p. 9).

Table 4 - Breaking load and abrasion resistance of finished fabrics

Name of fabric Breaking load of 50 to 200 tipi strips. H (ss). not less Abrasion resistance on a plane, cycles. on the basis Dress with areal density. g / m g: up to 100 incl. St. 100 "200" Satin weave: carded combed Combed with surface density, g / m -1: up to 250 incl. With split pile with surface density, g / m2: up to 300 inclusive. Shirts: from single yarn twisted yarn Lingerie with areal density. g / m *: up to 110 incl. St. 110 and 150 incl. including: greensbons corset Notes (edit) 1 For fabrics with an attachment of elastomeric threads, the "flat abrasion resistance" indicator is not determined 2 On the territory of the Russian Federation, the norms SanPiN 2.4.7 / 1.1.1286-03.

4.2.12 * Physical and hygienic indicators must meet the requirements specified in Table 5.

Table 5 - Physical and hygienic indicators

Name of fabric Air permeability, dm 3 / m 2 ■ s. no less Hygroscopicity. %, at a relative humidity of 98%, not less Specific surface electrical resistance. Ohm. no more Pay: cotton mixed Shirts: cotton mixed linen. cotton mixed For children (for all tissue groups): up to 1 g older than 1 g Note - It is allowed to decrease the air permeability index to 75 dm 3 / m 2 - s for starting sled cotton and blended fabrics.

See the note of the Federal State Unitary Enterprise "STANDARDINFORMr" (p. 9).

4.2.13 Whiteness of bleached fabrics - not less than 82%.

4.2.14 Permissible deviations of areal density,%:

for finished fabrics - not less than minus 5:

for ready-made fabrics with split pile - at least minus 7.

Permissible deviations in the number of threads per 10 cm for finished fabrics,%:

on the basis - ± 2;

for weft - ± 3, and for fabrics with split pile - ± 4.

4.2.15 In the technical description for a specific dressing (article) of finished and gray fabric, the following indicators should be established: composition of raw materials, linear density of yarn, number of threads per 10 cm along the warp and weft, areal density, fabric width, breaking load, size change after wet processing of finished fabric, abrasion resistance on the plane, type of finish and weave.

For fabrics used for the manufacture of items of clothing, technical descriptions must be agreed with the customer.

4.2.16 By agreement between the consumer and the manufacturer, additional requirements may be established in the technical description that are not provided for in this standard.

4.3 Marking

4.3.1 Primary marking of fabrics - according to GOST 30084.

4.3.2 Transport marking - according to GOST 7000.

4.4 Packaging

4.4.1 Primary packing of fabrics - according to GOST 8737. harsh fabric - according to the normative document.

4.4.2 Packing of fabric for transportation and storage - in accordance with GOST 7000.

5 Acceptance rules

Acceptance of fabrics - in accordance with GOST 20566.

Acceptance of fabrics of clothing property - in accordance with GOST 21768.

6 Test methods

6.1 Sampling of fabrics for testing - in accordance with GOST 20566.

6.2 Determination of linear dimensions and surface density - in accordance with GOST 3811.

6.3 Determination of the number of threads per 10 cm - according to GOST 3812.

6.4 Determination of breaking load - in accordance with GOST 3813.

6.5 Determination of hygroscopic and water-repellent properties - according to GOST 3816.

6.6 Determination of dimensional change after wet processing - according to GOST 30157.0 and GOST 30157.1.

6.7 Determination of air permeability - according to GOST 12088.

6.8 Determination of the degree of whiteness - according to GOST 18054.

6.9 Determination of abrasion resistance along the plane - according to GOST 18976 with the following addition: tests of fabrics with split pile are carried out on the wrong side of the fabric.

6.10 Determination of skew - according to GOST 14067.

6.11 Determination of the type and mass fraction of fibers, the degree of mercerization and the amount of free formaldehyde on the fabric - according to GOST 25617 and ISO 1833.

6.12 Determination of color fastness - according to GOST 9733.0, GOST 9733.1 or GOST 9733.3, GOST 9733.4. GOST 9733.6 (method II), GOST 9733.7, GOST 9733.13; determination of the color fastness of fabrics to dry friction - according to GOST 9733.27 with the following addition: from each point sample of cotton and mixed fabric, one elementary sample is cut out in the longitudinal direction.

6.13 Determination of specific surface electrical resistance - according to GOST 19616.

7 Safety requirements

Yarn, as well as all textile auxiliaries, finishing preparations and dyes used in the production of fabrics, which are subject to the requirements of this standard, must be produced in accordance with a regulatory document agreed in the established manner with the health authorities.

8 Transport and storage

Transportation and storage of fabrics - in accordance with GOST 7000.

Key words: cotton fabrics, mixed fabric, dress fabrics, shirts, underwear. final finishing, belongings

NOTE FSUE "STANDARTINFORM"

Amendments have been published in the information signs "National Standards":

UDC 677.21.074.006.354: 006.354 MKS 59.080.30 M63 OKP83YUOO

Key words: cotton fabrics, mixed fabric, dress fabrics, shirts, linen, finishing, clothing

Editor L.V. Koretmikooa Technical editor V.N. Prusakova Proofreader M.V. Naleyaimoi

Put in a set 22.05.200 € Signed for printing 26.06 2006. Format 60-84 ^ Offset paper. Arial headset.

Offset printing. Uel. pm p. 1.40. Uch.-over. l. 0.90. Circulation 441 copies Zak. 434. C 2982.

FSUE kStandartinform ". 123995 Moscow. Granatny lane .. 4. ww.v gostin "o.ru [email protected]

Typeset at FSUE "Standartinforms" on a PC Printed at the branch of FSUE "Standartinforms - typ. "Moscow printer". 105062 Moscow. Lyalin lane .. 6.

INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION

INTERSTATE COUNCIL FOR STANDARDIZATION. METROLOGY AND CERTIFICATION

INTERSTATE

STANDARD

COTTON AND FABRIC FABRICS FOR DOMESTIC

General specifications

Official edition

Foreword 1

The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic provisions "and GOST 1.2-97" Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. The procedure for development, acceptance, application, updating and cancellation "

Information about the standard

1 DEVELOPED by the Federal State Unitary Enterprise "Central Research Institute of the Cotton Industry" (FSUE TsNIKHBI)

2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology

3 ACCEPTED by the Interstate Council for Standardization, Metropology and Certification (Minutes No. 28 dated December 9, 2005)

Short name of the country according to MK<ИСО 3166) 004-97	Country code according to MK (ISO 31vv) 004-97	Abbreviated name of the national standardization body
		Armgosstandart
Kazakhstan		Gosstandart of the Republic of Kazakhstan
Kyrgyzstan		Kyrgyzstandard
		Moldova-Standard
the Russian Federation		Federal Agency for Technical Regulation
		nyu and metrology
Tajikistan		Tajikstandart
Turkmenistan		Glavgossluzkba "Turkmenstandartlary"
		State Standard of Ukraine

4 By order of the Federal Agency for Technical Regulation and Metrology dated May 10, 2006 No. 90-st, the interstate standard GOST 29298-2005 was put into effect as a national standard of the Russian Federation from January 1, 2007.

5 REPLACE GOST29298-92

Information on the entry into force (termination) of this standard is published in the index "National standards".

Information about changes to this standard is published in the index (catalog) "National standards". and the text of the changes is in the information signs "National Standards". In case of revision or cancellation of this standard, the corresponding information will be published in the information index "National standards"

In the Russian Federation, this standard cannot be fully or partially reproduced, replicated and distributed as an official publication without the permission of the Federal Agency for Technical Regulation and Metrology.

See the note of the Federal State Unitary Enterprise "STANDARTINFORM" (p. 9).

© STANDARTINFORM, 2006 © STANDARTINFORM. 2008 Reprinted (as of May 2008)

INTERSTATE STANDARD

COTTON AND MIXED FABRICS FOR HOUSEHOLD General specifications

Cotton and mixed domestic fabrics. General specifications

Date of introduction - 2007-01-01

1 area of ​​use

This standard applies to ready-made and gray cotton and blended fabrics used for the manufacture of products for dress, shirt and linen purposes, as well as items of clothing.

4.2.4 Fabrics are produced mercerized and not mercerized.

4.2.5 Fabrics, depending on the purpose, are produced with one of the types of finishing finishes. At the request of the consumer, the fabric is produced without finishing.

4.2.6 The fabrics used for the products of the children's assortment in terms of raw material composition must meet the requirements of the regulatory document. Fabrics for underwear assortment used for newborns and children of early, toddler and preschool ages must be produced without finishing.

4.2.7 Resizing after wet processing of finished fabrics must comply with the requirements. specified in table 2.

Table 2 - Change in dimensions after wet processing

Name of fabric Resizing after wet processing. %. less on the basis Dress (for dresses, blouses, dress suits, dressing gowns, shirts): Wrinkle-free finish, easy-ironing finish With an anti-shrink chemical finish, with a squeeze-out sizing agent based on thermosetting resins Shirts: Wrinkle-free finish, easy-ironing finish With an anti-shrink chemical finish, with a washable, thermosetting resin based finishing agent With a washable thermoplastic resin finish Lingerie: for underwear: Easy-iron finish, with a washable thermosetting resin finish With a washable thermoplastic resin finish for bed linen (including children without finishing) Notes (edit) 1 Fabrics with split pile are subjected to: corduroy cord and corduroy scar - dry cleaning or wet processing, velvet - dry cleaning. 2 For fabrics containing elastomeric threads, the change in linear dimensions after wet processing is not define.

4.2.8 Nominal widths for finished hemmed fabrics represent an integer of 70 cm or more ending in zero or five.

Tolerances for the width of fabrics in accordance with table 3.

4.2.9 The width of the two edges of the fabric should be no more than, cm:

3.0 - for fabric with split pile;

3.5 - for fabrics produced on a shuttleless loom;

1.5 - for other fabrics.

4.2.10 Grade of finished fabrics - according to GOST 161; harsh fabrics - according to the normative document.

4.2.11 * Breaking load and abrasion resistance of finished fabrics must meet the requirements of Table 4.

"See the note of the Federal State Unitary Enterprise" STANDARTINFORM "(p. 9).

Table 4 - Breaking load and abrasion resistance of finished fabrics

Name of fabric Breaking load of 50 to 200 tipi strips. H (ss). not less Abrasion resistance on a plane, cycles. on the basis Dress with areal density. g / m g: up to 100 incl. St. 100 "200" Satin weave: carded combed Combed with surface density, g / m -1: up to 250 incl. With split pile with surface density, g / m2: up to 300 inclusive. Shirts: from single yarn twisted yarn Lingerie with areal density. g / m *: up to 110 incl. St. 110 and 150 incl. including: greensbons corset Notes (edit) 1 For fabrics with an attachment of elastomeric threads, the "flat abrasion resistance" indicator is not determined 2 On the territory of the Russian Federation, the norms SanPiN 2.4.7 / 1.1.1286-03.

4.2.12 * Physical and hygienic indicators must meet the requirements specified in Table 5.

Table 5 - Physical and hygienic indicators

Name of fabric Air permeability, dm 3 / m 2 ■ s. no less Hygroscopicity. %, at a relative humidity of 98%, not less Specific surface electrical resistance. Ohm. no more Pay: cotton mixed Shirts: cotton mixed linen. cotton mixed For children (for all tissue groups): up to 1 g older than 1 g Note - It is allowed to decrease the air permeability index to 75 dm 3 / m 2 - s for starting sled cotton and blended fabrics.

See the note of the Federal State Unitary Enterprise "STANDARDINFORMr" (p. 9).

4.2.13 Whiteness of bleached fabrics - not less than 82%.

4.2.14 Permissible deviations of areal density,%:

for finished fabrics - not less than minus 5:

for ready-made fabrics with split pile - at least minus 7.

Permissible deviations in the number of threads per 10 cm for finished fabrics,%:

on the basis - ± 2;

for weft - ± 3, and for fabrics with split pile - ± 4.

4.2.15 In the technical description for a specific dressing (article) of finished and gray fabric, the following indicators should be established: composition of raw materials, linear density of yarn, number of threads per 10 cm along the warp and weft, areal density, fabric width, breaking load, size change after wet processing of finished fabric, abrasion resistance on the plane, type of finish and weave.

For fabrics used for the manufacture of items of clothing, technical descriptions must be agreed with the customer.

4.2.16 By agreement between the consumer and the manufacturer, additional requirements may be established in the technical description that are not provided for in this standard.

4.3 Marking

4.3.1 Primary marking of fabrics - according to GOST 30084.

4.3.2 Transport marking - according to GOST 7000.

4.4 Packaging

4.4.1 Primary packing of fabrics - according to GOST 8737. harsh fabric - according to the normative document.

4.4.2 Packing of fabric for transportation and storage - in accordance with GOST 7000.

5 Acceptance rules

Acceptance of fabrics - in accordance with GOST 20566.

Acceptance of fabrics of clothing property - in accordance with GOST 21768.

6 Test methods

6.1 Sampling of fabrics for testing - in accordance with GOST 20566.

6.2 Determination of linear dimensions and surface density - in accordance with GOST 3811.

6.3 Determination of the number of threads per 10 cm - according to GOST 3812.

6.4 Determination of breaking load - in accordance with GOST 3813.

6.5 Determination of hygroscopic and water-repellent properties - according to GOST 3816.

6.6 Determination of dimensional change after wet processing - according to GOST 30157.0 and GOST 30157.1.

6.7 Determination of air permeability - according to GOST 12088.

6.8 Determination of the degree of whiteness - according to GOST 18054.

6.9 Determination of abrasion resistance along the plane - according to GOST 18976 with the following addition: tests of fabrics with split pile are carried out on the wrong side of the fabric.

6.10 Determination of skew - according to GOST 14067.

6.11 Determination of the type and mass fraction of fibers, the degree of mercerization and the amount of free formaldehyde on the fabric - according to GOST 25617 and ISO 1833.

6.12 Determination of color fastness - according to GOST 9733.0, GOST 9733.1 or GOST 9733.3, GOST 9733.4. GOST 9733.6 (method II), GOST 9733.7, GOST 9733.13; determination of the color fastness of fabrics to dry friction - according to GOST 9733.27 with the following addition: from each point sample of cotton and mixed fabric, one elementary sample is cut out in the longitudinal direction.

6.13 Determination of specific surface electrical resistance - according to GOST 19616.

7 Safety requirements

Yarn, as well as all textile auxiliaries, finishing preparations and dyes used in the production of fabrics, which are subject to the requirements of this standard, must be produced in accordance with a regulatory document agreed in the established manner with the health authorities.

8 Transport and storage

Transportation and storage of fabrics - in accordance with GOST 7000.

Key words: cotton fabrics, mixed fabric, dress fabrics, shirts, underwear. final finishing, belongings

NOTE FSUE "STANDARTINFORM"

Amendments have been published in the information signs "National Standards":

UDC 677.21.074.006.354: 006.354 MKS 59.080.30 M63 OKP83YUOO

Key words: cotton fabrics, mixed fabric, dress fabrics, shirts, linen, finishing, clothing

Editor L.V. Koretmikooa Technical editor V.N. Prusakova Proofreader M.V. Naleyaimoi

Put in a set 22.05.200 € Signed for printing 26.06 2006. Format 60-84 ^ Offset paper. Arial headset.

Offset printing. Uel. pm p. 1.40. Uch.-over. l. 0.90. Circulation 441 copies Zak. 434. C 2982.

FSUE kStandartinform ". 123995 Moscow. Granatny lane .. 4. ww.v gostin "o.ru [email protected]

Typeset at FSUE "Standartinforms" on a PC Printed at the branch of FSUE "Standartinforms - typ. "Moscow printer". 105062 Moscow. Lyalin lane .. 6.

Cotton technical fabrics are a durable and heat-resistant material used in a wide variety of industries. They are made from fiber of plant origin, which is formed in the capsules of the cotton plant. We offer you coarse calico, chintz, calico, flannel, linen and other types of cotton fabrics.

Name	vendor code	GOST / TU	Unit meas.	Compound	Width, cm	Density, g / m2	Average number of m.p. in a roll
Madapolam (bleached chintz)	43	GOST 29298-2005	m.	100% cotton	80	85+-5	100 lm
White earth chintz	43	GOST 29298-2005	m.	100% cotton	80	85+-5	100 lm
Chintz g / cr black	43	GOST 29298-2005	m.	100% cotton	80	85+-5	100 lm
Chintz gl / cr: red / burgundy	43	GOST 29298-2005	m.	100% cotton	80	85+-5	100 lm
Chintz light / cr .: yellow, pink., Blue	43	GOST 29298-2005	m.	100% cotton	80	85+-5	100 lm
Bleached calico GOST	142	GOST 29298-2005	m.	100% cotton	80	142+-7	70-80 lm
Bleached calico	142	GOST 29298-2005	m.	100% cotton	80	125+-7	80-100 lm
Bleached calico GOST	262	GOST 29298-2005	m.	100% cotton	150	142+-7	70-100 lm
Bleached calico	262	GOST 29298-2005	m.	100% cotton	150	125+-7	50-70 lm
Black calico	142	GOST 29298-2005	m.	100% cotton	80	125+-7	80-100 lm
Coarse calico gl / cr. Black / olive	262	GOST 29298-2005	m.	100% cotton	150	125+-7	70-80 lm
Coarse calico gl / cr. Salad., Blue, pink, yellow, peach, beige.	262	GOST 29298-2005	m.	100% cotton	150	125+-7	80-100 lm
Coarse calico gl / cr. Black / olive GOST	262	GOST 29298-2005	m.	100% cotton	150	142+-7	70-80 lm
Coarse calico	142	GOST 29298-2005	m.	100% cotton	92	130+-7	80-100 lm
Coarse calico	262	GOST 29298-2005	m.	100% cotton	160	130+-7	80-100 lm
Coarse calico severe GOST	262	GOST 29298-2005	m.	100% cotton	160	152-7	80-100 lm
Heavy coarse calico with fire retardant impregnation	1124	Impregnation according to GOST 19297-2003	m.	100% cotton	165+-2,5	146+-7	90-100 lm
Calico harsh	43	GOST 29298-2005	m.	100% cotton	92	85+-5	Bale 300-350, roll 50-180 lm
Fabric MELODY	1502	GOST 29298-2005	m.	100% cotton	85+-1,5	70+-0,1	100
Printed calico	262	GOST 29298-2005	m.	100% cotton	150	125+-7	70-100 lm
Printed coarse calico white earth	262	GOST 29298-2005	m.	100% cotton	150	125+-7	70-100 lm
Printed calico	262	GOST 29298-2005	m.	100% cotton	220	130+-7	50-60 lm
Printed coarse calico b / s and o / m GOST	262	GOST 29298-2005	m.	100% cotton	150	142+-7	70-80 lm
Flannel gl / cr (light cr)	1681	GOST 29298-2005	m.	100% cotton	75	175+-5	45-70 lm
Flannel gl / cr. (olive, black)	1681	GOST 29298-2005	m.	100% cotton	75	175+-5	45-70 lm
Flannel for children	1681	GOST 29298-2005	m.	100% cotton	75	175+-5	45-70 lm
Flannel bleached	1681	GOST 29298-2005	m.	100% cotton	75	175+-5	50-70 lm
Flannel dressing gown, shirt	1981	GOST 29298-2005	m.	100% cotton	75	175+-5	45-70 lm
The bike is harsh	C47-EX	TU 8310-13299377-019-2006	m.	100% cotton	85+-1,5	360+-18	40-60 lm
Bike gl / cr. (olive)	1141-E	TU 858-5732-2005	m.	100% cotton	80	355+-18	40-60 lm
Bumazey gl / cr	S1650-EX	TU 858-5733-2005 to GOST 29298-2005	m.	100% cotton	80+-1,5	255+-13	40-60 lm
Bleached waffle cloth.	402	GOST 29298-2005	m.	100% cotton	40	175+-5	60-80 lm
Bleached waffle cloth.	402	GOST 29298-2005	m.	100% cotton	45	175+-5	50-60 lm
Bleached waffle cloth.	402	GOST 29298-2005	m.	100% cotton	80	175+-5	45-55 lm
	8098	GOST 29298-2005	m.	100% cotton	50	200+-5	50-60 lm
Bleached waffle cloth. GOST	8098	GOST 29298-2005	m.	100% cotton	45	240+-5	45-60 lm
Waffle linen fabric, harsh	C32-EX	TO 8317-13299377-022-2006	m.	100% cotton	46+1,5	163+-8	45-60 lm
The diagonal is severe	3515	Depends on the manufacturer's factory	m.	100% cotton	90	205+-12	50-80 lm
The diagonal is severe	505		m.	100% cotton	90	250+-12	50-70 lm
Bleached diagonal	3515		m.	100% cotton	85	205/240	45-50 lm
	3515		m.	100% cotton	85	205+-11	45-50 lm
Diagonal gl / red, black / blue	3515		m.	100% cotton	85	240+-11	45-50 lm
The diagonal is camouflaged.	3515		m.	100% cotton	85	205+-11	45-50 lm
Severe two-thread	1904		m.	100% cotton	90	185+-11	50-80 lm
Severe two-thread	105		m.	100% cotton	90	214+-11	50-80 lm
	21HF		m.	100% cotton	90	219+-11	45-50 lm
Double-strand, rough, finished	21HF		m.	100% cotton	90	245+-11	45-50 lm
Mattress teak with black Awake	-		m.	100% cotton	165	190+-9	80-100 lm
Mattress teak with color Awake	-		m.	100% cotton	165	150/175	80-100 lm
Tick ​​ch. cr. pillowcase	4006		m.	100% cotton	150	190+-9	80-100 lm
Tick ​​ch. cr. pillowcase	4006		m.	100% cotton	80	190+-9	80-100 lm

page 1

page 2

p. 3

p. 4

p. 5

page 6

page 7

page 8

page 9

p. 10

page 11

p. 12

INTERSTATE COUNCIL FOR STANDARDIZATION. METROLOGY AND CERTIFICATIONS

INTERSTATE COUNCIL FOR STANDARDIZATION. METROLOGY AND CERTIFICATION

INTERSTATE

STANDARD

COTTON AND FABRIC FABRICS FOR DOMESTIC

General specifications

Official edition

Standardinform

Foreword 1

The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic provisions "and GOST 1.2-97" Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. The order of development, adoption, application. updates and cancellations "

Information about the standard

1 DEVELOPED by the Federal State Unitary Enterprise "Central Research Institute of the Cotton Industry" (FSUE TsNIHBI)

2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology

3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (Minutes No. 28 dated December 9, 2005)

Country short name no MK (ISO 3166) 004-97	Country code according to MK (ISO 3166) 004-97	Abbreviated name of the national standardization body
		Armgosstandart
Kazakhstan		Gosstandart of the Republic of Kazakhstan
Kyrgyzstan		Kyrgyzstaidart
		Moldova-Standard
the Russian Federation		Federal Agency for Technical Regulation
		nyu and metrology
Tajikistan		Tajikstandart
Turkmenistan		Glavtossluzhba "Turkmenstandartlary"
		State Standard of Ukraine

4 By order of the Federal Agency for Technical Regulation and Metrology of May 10, 2006 No. 90-st, the interstate standard GOST 29298-2005 was put into effect as a national standard of the Russian Federation from January 1, 2007.

Information on the entry into force (termination) of this standard is published in the index "National standards".

Information about the changes to this standard is published in the index (catalog) "National standards", and the text of the changes - in the information indexes "National standards". In case of revision or cancellation of this standard, the corresponding information will be published in the information index "National standards"

In the Russian Federation, this standard cannot be reproduced in whole or in part. replicated and distributed as an official publication without the permission of the Federal Agency for Technical Regulation and Metrology

INTERSTATE STANDARD

COTTON AND MIXED FABRICS FOR HOUSEHOLD General specifications

Cotton and mixed domestic fabrics. General specifications

Date of introduction - 2007-01-01

1 area of ​​use

This standard applies to ready-made and gray cotton and blended fabrics used for the manufacture of articles of dress, shirts and linen, as well as items of clothing.

2 Normative references

4,2.4 Fabrics are produced mercerized and not mercerized.

4, 2.5 Fabrics, depending on the purpose, are produced with one of the types of finishing finishes. At the request of the consumer, the fabric is produced without finishing.

4.2.6 The fabrics used for the products of the children's assortment in terms of raw material composition must meet the requirements of the regulatory document. Fabrics for underwear assortment used for newborns and children of early, toddler and preschool ages must be produced without finishing.

4.2.7 Changes in dimensions after wet processing of finished fabrics must comply with the requirements specified in table 2.

Table 2 - Change in dimensions after wet processing

Name of fabric Change in dimensions after wet processing,%. but boleo on the basis Dress (for dresses, blouses, dress suits, dressing gowns, shirts): Shirts; Wrinkle-free finish, easy-ironing finish With an anti-shrink chemical finish, with a low-washable size based on thermosetting resins With low-washable thermoplastic resin-based sizing Lingerie: for underwear. With an easy-iron finish, with a low-washable finishing agent based on thermosetting resins With low-washable thermoplastic resin-based sizing for bed linen (including for children without finishing)

Notes (edit) 1 Fabrics with split pile are subjected to: corduroy cord and corduroy scar - dry cleaning or wet processing; velvet - dry clean. 2 For fabrics containing elastomeric threads, the change in linear dimensions after wet processing is not 1 define .__

4.2.8 Nominal widths for finished hemmed fabrics represent an integer of 70 cm or more ending in zero or five.

Tolerances for the width of fabrics in accordance with table 3.

4.2.9 The width of the two edges of the fabric should be no more than, cm:

3.0 - for fabric with split pile;

3.5 - for fabrics produced on a shuttleless loom;

1.5 - for other fabrics.

4.2.10 Grade of finished fabrics - according to GOST 161; harsh fabrics - according to the normative document.

4.2.11 * Breaking load and abrasion resistance of finished fabrics must meet the requirements of Table 4.

Table 4 - Breaking load and abrasion resistance of finished fabrics

Name of fabric Breaking load of a strip of fabric measuring 50 ■ 200 mm. N (yas). not less Abrasion resistance on a plane, cycles. on the basis Dress with areal density. g / m 2: up to 100 incl. St. 100 "200" Satin weave: carded combed Combed with areal density. g / m 2: up to 250 incl. With split pile with a surface lean density, g / m 2: up to 300 incl. Shirts: from single yarn twisted yarn Lingerie with areal density. g / m 2: up to 110 incl. behold. 110 "150 incl. including: greensbons corsetry _

Notes (edit)

1 For fabrics with an attachment of elastomeric threads, the indicator "abrasion resistance in the plane" is not determined.

2 On the territory of the Russian Federation, the norms of SanPiN 2.4.7 / 1.1.1286-03 apply.

4.2.12 * Physical and hygienic indicators must meet the requirements specified in Table 5.

Table 5 - Physical and hygienic indicators

Name of fabric Air permeability. dm 3 / m g ■ s. not less Hygroscopicity. %. at a relative humidity of 98%. not less Specific surface electrical resistance. Ohm. no more Pay; clap you big mixed Shirts: cotton mixed Lingerie. cotton mixed For children (for all tissue groups): older than 1 g Noting and e - It is allowed to reduce the air permeability indicator to 75 dm 3 / m 2 s for an initial sled cotton and blended fabrics.

See the note of the Federal State Unitary Enterprise "STANDARTINFORM" (p. 9).

4.2.13 Whiteness of bleached fabrics - not less than 82%.

4.2.14 Permissible deviations of areal density,%:

for finished fabrics - at least minus 5;

for ready-made fabrics with split pile - at least minus 7.

Permissible deviations in the number of threads per 10 cm for finished fabrics,%:

on the basis - ± 2:

on the weft - = 3, and for fabrics with split pile - g 4.

4.2.15 In the technical description for a specific dressing (article) of finished and gray fabric, the following indicators should be established: composition of raw materials, linear density of yarn, number of threads per 10 cm along the warp and weft, areal density, fabric width, breaking load, size change after wet processing of finished fabric, abrasion resistance on the plane, type of finish and weave.

For fabrics used for the manufacture of items of clothing, technical descriptions must be agreed with the customer.

4.2.16 By agreement between the consumer and the manufacturer, additional requirements may be established in the technical description that are not provided for in this standard.

GOST 25617

8 Transport and storage

Transportation and storage of fabrics - in accordance with GOST 7000.

UDC 677.21.074.006.354: 006.354 MKS 59.080.30 M63 OKP83YUOO

Key words: cotton fabrics, mixed fabric, dress fabrics, shirts, underwear. final finishing, belongings

See the note of the Federal State Unitary Enterprise "STANDARTINFORM" (p. 9).

© STANDARTINFORM, 2006 © STANDARTINFORM. 2008 Reprinted (as of May 2008)

Iedanio official